Feldherr MINI PLUS Review (Magnetic Case for Small Armies)

Published October 4, 2026. Last updated October 4, 2026. By Andrew M. Tan.

The dimensions and corrosion-resistance claims above come from Feldherr’s product listing; I did not independently measure every component or test the tray coating for corrosion. For packing, tray area and usable clearance matter more than a generic model-count claim. Check your base footprints, poses, wings, banners, and magnet placement against those measurements. This thing is compact.

What Comes With the Feldherr MINI PLUS Magnetic Case

The set Feldherr sent includes the black MINI PLUS bag, the rigid red HSVR7150 transport case, and two matching HSTRAY_7150_red magnetic trays. Everything arrived neatly wrapped and ready for me to load with magnetized miniatures.

The outer bag has the Feldherr badge on the front and a transparent label pocket on the back. The label pocket is a small thing, though it becomes useful when several black hobby bags begin multiplying in a closet. They do that.

The rigid Half-Size case fits closely inside the MINI PLUS bag. Its side walls provide seven tray positions, and the left and right sides can be offset. That uneven spacing is useful when a banner, wing, weapon, or tall base needs a little more room than the model beside it.

Feldherr describes the trays as powder-coated steel and corrosion-resistant. In my hands, they felt flat, solid, and cleanly finished, with no distracting play after I slid them into the frame. I did not perform a corrosion test.

The useful part of this system is its simplicity. Load a tray, choose a height, slide it in, and lock the frame.

How Well Do Magnetized Miniatures Hold

My Imperial Fists already have rare-earth magnets glued beneath their bases. I placed infantry on the upper tray and larger models on the lower tray, then moved the shelves into position.

The magnets grabbed the black metal surface immediately. The models stayed upright while I loaded the case and adjusted the trays. Good contact matters here. A magnet that sits too far inside a recessed base will have a weaker hold because the gap reduces its pull against the steel.

Vehicles need a little more planning. I glued two magnets beneath my Rhino, and the model held securely on the tray during this test. Heavier resin models may need larger magnets or several contact points.

When removing a strongly magnetized model, slide the base gently across the tray before lifting it. This peeling motion reduces the force on the glue joint beneath the base.

For a deeper look at setting up a magnetic collection, my budget magnetic carrying-case review and magnetizing guide covers magnet sizes, glue, epoxy putty, and practical attachment tips.

How Much Fits Inside

The MINI PLUS name is honest. This is a small case.

I could arrange infantry, a standard bearer, and several larger models across the two trays. Vehicles fit on the lower level, and the multiple slot heights let me preserve clearance above them. Taller infantry can sit on the upper tray where the open space extends toward the top of the frame.

Feldherr sells the trays separately, so you can keep several loaded in a display cabinet and move only the trays you need into the case. That makes the system easier to expand, although every added tray costs extra and consumes some vertical clearance. The flexibility helps you use the available volume well. It does not create more volume.

For Kill Team, Warcry, small Infinity forces, a compact display collection, or a selected group of Warhammer 40K models, the size makes sense. You can carry what you need without hauling a cabinet on your shoulder.

A full tournament army will fill this case quickly. Large monsters, flyers, banners, and vehicles consume the available space in a hurry. The exact capacity depends on base size and model height, so a model count would be misleading.

Think in tray area and vertical clearance. Those two measurements matter more than army points.

The Tray Lock Is the Smartest Detail

A small switch sits near the upper corner of the rigid frame. Turning it closes a gate across the tray slots and keeps the shelves from sliding forward.

I like this design because one control secures every installed tray. There is no separate pin to lose and no latch to fasten on each shelf.

During my tilt test, the locked trays stayed inside the frame. The miniatures still depend on their own magnets, so tray security and model security remain two separate checks. Test both before carrying the case into the wilds of a convention parking lot.

The switch also has a visible color indicator. A quick glance tells you whether the gate is open or closed. Feldherr also lists the case as padlock compatible, although a padlock is not included, and fits the bottom with non-slip pads for stability while pulling out a tray. My hands-on test focused on tray retention, not theft resistance or long-term pad wear.

The Outer Bag Keeps the System Portable

The hard-wearing black MINI PLUS bag wraps around the rigid case and closes with a zipper. Feldherr lists the interior at approximately 275 × 172 × 150 mm and the exterior at approximately 300 × 200 × 160 mm. A carry handle makes the compact setup easy to grab, while the fabric keeps the bright red frame from becoming its own piece of luggage.

Inside the front flap is a zippered mesh pocket. I could use it for dice, tokens, cards, reference sheets, measuring tools, or other small game accessories. It is shallow enough that I would leave a full rulebook elsewhere.

The bag’s label pocket is another practical touch for people who organize armies by faction or game. Write the contents on a card, slide it into the pocket, and spare yourself the ritual of opening three identical cases to find the fourth one.

What I Like

• The rigid frame arrives ready to use.
• The steel trays feel solid and slide cleanly into the molded slots.
• Seven tray positions support several model heights.
• A single switch locks every tray inside the case.
• The compact footprint suits skirmish games and casual game nights.
• The bag includes a handle, label pocket, and small accessory pocket.
• Vehicles and taller models can fit when the trays are spaced thoughtfully.

What Could Be Better

• Only two trays are included; matching trays are sold separately and add to the total cost.
• Large armies will outgrow the case quickly.
• Tall models reduce the room available for another loaded tray.
• Base magnets are required and sold separately.
• A padlock is optional but not included.
• The inner accessory pocket is too small for many full-size rulebooks.
• I have not completed a long-term durability test of the zipper, bag fabric, plastic frame, tray coating, or non-slip pads.

Who Should Buy This Case

The Feldherr MINI PLUS magnetic case makes the most sense for a player who already owns a magnetized collection and wants a small, organized travel setup.

I would consider it for:

• Kill Team and other skirmish games
• Small Warhammer 40K or Age of Sigmar forces
• Infinity, Malifaux, and similar low-model-count games
• A painting competition entry and a few supporting models
• A handpicked display collection for local game night
• Hobbyists who value a compact footprint over maximum capacity

The case becomes less practical when your force depends on many vehicles, tall banners, large monsters, or several trays of infantry. My guide to magnetic miniature transport cases includes larger systems for those situations.

The Feldherr occupies a different role from a large display-style carrier. It is easier to place on a shelf, easier to grab for a small game, and easier to fill without bringing models you never planned to use.

For foam-based choices and other carrying styles, see my broader guide to miniature transport cases and bags. My hands-on Citadel Crusade Case review also explains where channel foam still makes sense for models without magnets.

---

Tangible Day on YouTube (Miniatures and More!)

---