Recommended Varnishes for Miniatures (Best Practice and Use)

Recommended Matte Varnishes for Miniatures (Best Practice and Use)

So, you’ve spent hours painting miniatures. Now, you want to protect your work. If you’re a gamer, this is especially important since your models will have to endure a lot of handling. To protect your minis, you need to seal them with a varnish. Varnishes also improve photographs of your models. There is a need to varnish your miniatures. What are the best matte varnishes for miniatures and models?

Advertisements

In this article, I provide the core information you need to know for properly varnishing your models for gaming, display, or photography.

Read on for more!


The Two Varnishes I Currently Use to Protect My Miniatures and Highly-Recommend Are:

1. Testors Dullcote “Spray” Lacquer

Recommended Matte Varnishes for Miniatures (Best Practice and Use)
Spray-on Testors Dullcote enamel varnish

I use this on every miniature that I finish painting. This is the best spray-on enamel varnish you can buy for our painting hobby. It comes in a small can, but lasts a long time. I’ve covered at least a hundred 28mm scaled miniatures with a single can.

The varnish from Testors Dullcote spray dries into a hard, matte-finish. This means that my varnished miniatures retain their overall color saturation, while at the same time gain an even non-reflective surface.

WANT BETTER MINIATURE PHOTOS? CONSIDER A PHOTO LIGHT BOX

This is particularly great for photography where you want to reduce “hotspot” light reflections. Check out my gallery where you can see models that I used Testors Dullcote on.

QUICK TIPS FOR TESTORS DULLCOTE SPRAY VARNISH

  • Spray more than 6″ away from the miniature
  • Don’t use in ambient humidity greater than 50%
  • Try using a hairdryer before and after spraying to avoid “frosting”
Recommended Matte Varnishes for Miniatures (Best Practice and Use)
Testors Dullcote helps with photography – the matte varnish removes hotspot reflections and creates an evenly lit surface. This Imperial Knight for Warhammer 40k is a good example of using a varnish for enhancing the overall display quality of high-contrast models.

2. Testors Dullcote Lacquer “Brush On”

Recommended Matte Varnishes for Miniatures (Best Practice and Use)
Brush-on Testors Dullcote enamel varnish

In general, a spray-on varnish is the best way to achieve an even coat of varnish. However, there are specific uses for a brush-on varnish. First, a brush-on varnish is really helpful for the final sealant over wet-slide decals. If you’ve ever tried to apply wet transfer decals to a model, then you know how hard it can be to “hide” the sticker look. A thin coat of brush-on Testors Dullcote will help merge the decal texture with the painted model underneath.

Second, a brush-on enamel based varnish like Testors Dullcote hardens into a fairly rigid surface. This is useful for custom-made banners that you might printout on computer paper. Coating paper-made banners, capes, or other accessories on miniatures with Testors Dullcote protects the printer ink from bleeding from paper and helps hold their shape (see examples below). I use Testors Dullcote brush on primer often when I want to control the overall look of specific parts of a model.

QUICK TIPS FOR BRUSH-ON TESTORS DULLCOTE VARNISH

  • Apply in super-thin layers with a synthetic brush, e.g., a wide flat-thin brush
  • Clean off your brushes and work surface with clear mineral spirits or turpentine (Testors has a branded cleaner/thinner here)
  • Useful for concealing wet-slide decals on models (“a perfect finish”)
  • Protecting custom inkjet printed banners and standards
  • Try to apply the brush-on varnish on a horizontal surface to prevent running or sagging. If you’re applying on a vertical surface, only use very thin coats at a time.
Recommended Matte Varnishes for Miniatures (Best Practice and Use)
Brush on Testors Dullcote is very effective for concealing wet-slide decals. The wolf head decal on Canis Rex (40k Imperial Knight model) looks like it’s painted on. But, it’s not. The varnish sealant protects and hides the “sticker” look of decals.
Recommended Matte Varnishes for Miniatures (Best Practice and Use)
Testors Dullcote helps protect custom printed banners and flags. It also helps them keep their folded shape.
Advertisements

A Quick Guide for Using Varnishes on Miniatures

Recommended Matte Varnishes for Miniatures (Best Practice and  Use)
A guide for printout and sharing

In a non-scientific survey of several website forums and social media outlets (i.e., reddit, Facebook, Cool Mini or Not ‘CMON’ painting forums, etc), I found that almost all miniature painters agreed that varnishing was important for their gaming miniatures and board game models.

A few people suggested that varnishes aren’t necessary, especially when models were destined for display purposes only. However, the vast majority suggested that new miniature painters learn how to varnish their models with a matte finish. There are several key reasons why.

Recommended Varnishes for Miniatures (Best Practice and Use)
“Azathoth”” Cthulhu Wars

Varnishing miniatures is important for protecting the paint job and improving photography of the models. If you’re sharing images of your models, present them in the best light possible. Use a matte spray varnish to create an evenly lit surface across the entire miniature.

Read on further below for “how to correctly use a matte varnish”.

The best matte varnishes are spray-on type sealants, such as Testors Dullcote.

My Alternative to Testors Dullcote: a Water-Based Matte Varnish

Spraying a varnish is the best way to evenly coat a model. However, if you don’t want to use an enamel or lacquer (shellac) based varnish, such as Testors Dullcote, there are water-based alternatives. Testors Dullcote spray varnish is an aerosol based medium, which means that it could produce harmful vapors. Additionally, Testors Dullcote spray varnish is vulnerable to adverse “frosting” behavior if not applied under optimal conditions (low humidity <50%).

Liquitex Matte Varnish

In this case, you might want to try and alternative water-based matte varnish. I currently recommend Liquitex Matte Varnish. But, if you go in this route your best method for applying this varnish is to use an airbrush. Thin the varnish with water (approximately 1:1 ratio) and airbrush it onto your model.

Advantage of non-aerosol water-based varnishes: A huge side benefit of using a non-aerosol spray varnish, such as the Liquitex varnish is the cost-effectiveness of it. It is much, much cheaper to airbrush a non-aerosol water-based varnish than it is to use cans of aerosol lacquer spray varnishes.

Disadvantage of water-based varnishes: The disadvantage of water-based varnishes is that they are essentially acrylic mediums (with suspended dry particulates). This means they aren’t very different in composition to the paint you used to paint your miniatures. So, the varnish won’t be as durable or long-lasting as an enamel-based spray varnish like Testors Dullcote. It can be relatively easy to rub-off a water-based varnish (just soak a cotton tip in water and scrub).

Overall, I’d use a non-aerosol based varnish on models where you don’t want to create a hazardous environment for people (or pets) around me. Or, where you don’t want the strong odors from an aerosol to disturb others in my immediate surroundings (like if I’m working at a convention or trade show). Some models in my gallery have a water-based varnish coating, but I eventually cover these with a stronger enamel-based varnish for longer term storage and display.

Recommended Varnishes for Miniatures (Best Practice and Use)
A good varnish sealant protects miniatures (Cthulhu Wars figure) and helps maintain the color micro-contrast in photographic settings

Do I Need a Gloss Varnish Before a Matte Varnish?

This is a good question that arises from traditional art methods. For a 2D canvas painting, an “isolation” varnish coat is useful for long-term preservation of acrylic paintings. An isolation coat is usually a gloss medium and a permanent non-removable sealant that physical protects the paint surface from overlying varnishes. An isolation coat helps protect the painted canvas if there is every a need to clean or conserve the painting in the future.

An isolation coat also seals any absorbent surfaces on the painting. Acrylic paint absorbs water easily, so an isolation coat would decrease the chance of water entering into the painted surface. This provides additional protection for cleaning and dusting a canvas painting.

Recommended Matte Varnishes for Miniatures (Best Practice and Use)
Only apply as much varnish as you need to protect your model. Too many coats and you lose clarity and color saturation.

The #1 Reason You Want to Use a Gloss Varnish

An isolation coat (usually a gloss medium) prevents the “cloudy” or “frosted” appearance that can occur when applying a matte varnish (more about this below). Briefly, frosting or clouding can occur when a matte varnish is applied to a porous or absorbant surface. A matte varnish contains dry particulates (like microscopic powder), which provide the non-reflective attributes of the medium. These particulates are suspended in the varnish. When the matte varnish is applied via spraying, the solvent the particulates are in helps coat the surface evenly. When a surface is coated evenly before the solvent evaporates, the dry particulates act as a non-reflective and transparent surface.

However, if the solvent dries poorly (e.g., absorbed into the paint underneath or mixes with ambient moisture) the dry particulates previously in solution clump-up. This clumping, congealing, or aggregation of the powder-like substances in the matte varnish cause the cloudy, frost effect that obscures the paint job underneath. By using a gloss medium first (no particulates), you reduce the risk of the matte varnish appearing as a cloudy surface.

Recommended Varnishes for Miniatures (Best Practice and Use)
The dreaded “frosted” look with poorly applied matte varnish. The cloudy appearance reduces contrast and color saturation. It’s an unfortunate adverse effect of using matte varnishes without proper conditions (see more about how to prevent and solve this issue below).
Advertisements

The Reason You Don’t Want to Use a Gloss Varnish

For miniatures, there is no added benefit in terms of protection for your models. A gloss varnish will not make the overlaying matte varnish stronger or more durable. You’re merely adding extra layers of a transparent medium over your model.

If anything, adding that extra layer of gloss varnish may reduce the amount of detail and color that shows through the final coating. Each layer of varnish reduces the “clarity” of the paint job underneath. As a routine procedure, I try to apply no more than 3-4 layers of any varnish.

How to Prevent the “Cloudy” or “Frosted” Appearance When Applying a Matte Varnish

Okay, so we’ve decided that you don’t want to use an isolation coat gloss varnish before applying the matte varnish. But, you don’t want your hours-long paint job to be ruined because of a poorly applied matte varnish that clouds over.

Here’s what you can do to prevent the frosted appearance of miniatures when you use a matte varnish:

  • Shake the spray matte varnish can vigorously for at least 60 seconds
    • This ensures that the varnish solvent and the powder/particulates in the matte varnish are mixed.
    • If you can cool your aerosol spray varnish down (~12C or 53F) before spraying it, this will also help prevent the frosted effect.
  • Spray a matte varnish when the ambient humidity is less than 50%
    • Water moisture in the air may be absorbed into your acrylic paint (on your miniature), which then interacts with how the matte varnish coats your model. Acrylic paint loves to absorb water (even when you think its dry).
    • Water moisture in the air can also interact with the solvent from your matte varnish spray as it travels toward your model, creating an uneven coated surface
    • Any of these humidity-related factors can contribute to a poor coating of the matte varnish, ultimately leading to the matte particulates in the medium clumping up and forming an opaque, cloudy surface.
    • You can get a humidity gauge/monitor from a cigar shop or online
  • Use a hair dryer to reduce the moisture on the model and the local air around the miniature
    • I strongly advocate the use of hair dryer for all kinds of purposes in miniature painting.
    • A low-cost hair dryer removes ambient moisture and warms the models, which reduces the chance that water on the surface of the model will disrupt the spray application of the matte varnish.
    • Hold your hair dryer about 6-12 inches from the model and apply hot air until you feel the model is warm to the touch. Then, spray the matte varnish as you normally would in a thin layer. Re-apply the hair dryer heat until the solvent evaporates from the matte varnish. The result should be a fully clear, transparent and non-reflective surface.
Advertisements

How to Restore a “Frosted” Miniature Following a Matte Varnish Application

Oh no!

Did you just ruin your miniature with a frosted matte varnish?

The following methods work with aerosol based spray matte varnishes, such as Testors Dullcote, Army Painter, Krylon, and GW Citadel matte spray varnishes. Because of the similarities of these varnish formulations, the methods for restoring frosted models should also work for other solvent based spray laquer/shellac-type matte varnishes.

A proven 5-step method for restoring models that have a badly frosted finish:

  1. Use olive oil
  2. Apply a thin coat of virgin olive oil over the entire miniature.
  3. Let this coat of oil dry (or “cure”, which is the appropriate term) on the model for at least 1-2 hours. The olive oil removes or displaces some of the moisture on the model’s surface and lubricates the dried particulates that cause the frosted effect. As the oil cures, the varnished surface smooths out which helps restore the transparent effect.
  4. After a little time has elapsed, wipe off the oil with a clean paper cloth. Most the transparency should have returned to the miniature. You can carefully wipe off the oil from the model with a dampened paper towel with soap and water (do not soak the miniature).
  5. After the model has dried, re-apply the matte varnish using the frost-prevention methods described above.
Recommended Varnishes for Miniatures (Best Practice and Use)
Before and after olive oil application – notice the restoration of color and clarity of the previously “frosted” model

Final Thoughts

These are the 3 best varnishes I recommend for sealing miniatures after an acrylic paint job.

  1. Testors Dullcote “Spray” Lacquer
  2. Testors Dullcote Lacquer “Brush On”
  3. Liquitex Matte Varnish

You don’t need a gloss varnish to improve the protective qualities of a matte varnish. But, an isolation coat with a gloss varnish can prevent “frosting” of a matte varnish. Ensure proper ambient conditions to reduce the risk of a matte varnish clouding over a painted model. Don’t fret, however, a miniature with a poorly applied varnish can be restored with a few simple steps.

Sealing your miniatures with a high quality varnish is the final step to a completed paint job. You’ll be happy you took the time to protect your models! They will look great for photographs, too!


Like It? Share It!

Did you find this article helpful? I’d love to hear from you 🙂

Leave a comment below! Subscribe through email or follow Tangible Day on Facebook, Pinterest, and Instagram.

Advertisements

1 thought on “Recommended Varnishes for Miniatures (Best Practice and Use)”

  1. Pingback: Learning Bench 2019-10-30 – Hobby Painting Brussels

Leave a comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.

%d bloggers like this: